Решение проблем с NBTEVO, Коды FSC для BMW -----> Получить - жмите ссылку |
BMW NBT EVO FATAL ERROR SWFL 0000271a
#1
Отправлено 06 июня 2017 - 14:08
#2
Отправлено 24 августа 2017 - 08:00
Hello!
I have the same problem with 2 B140 units, have you managed to solve it?
#3
Отправлено 24 августа 2017 - 08:13
MCDDiagService<id=36900, job=com.bmw.psdz.jobs.uds.MCD3_PerformECUFlash, service=RDBI_ADS - ReadDataByIdentifier ActiveDiagnosticSession, description=error: timeout, link=Physical request to ECU with address 0x63>
Прикрепленные файлы
#4
Отправлено 24 августа 2017 - 09:00
#5
Отправлено 24 августа 2017 - 09:22
Looks like your EVOs have been opened and not properly reassembled. HDD or DVD drive is not properly connected. Make sure to unscrew the adapter board before inserting it into DVD, then screw it back together when DVD is already attached to a connector. Check the drive status in Tool32. If your HDD or DVD is not found, you would not be able to flash 271a - it tries to update the drive firmware and fails when no drive is found. It took me a while to figure this one out. DVD connector is a PITA to connect properly. Must be an easter egg from BMW.
- MeMpHiSj и golomazzz_30 это нравится
#6
Отправлено 24 августа 2017 - 11:54
Для тех кто не дружит с иностранными языками - на EVO не прошивается SWFL 0000271a. Причина может быть в неисправных приводах или неверном соединении DVD. Если открывать верхнюю крышку, поставить на место DVD привод без откручивания платы-адаптера у меня лично не получилось после нескольких попыток. DVD выглядит как будто установлен верно, но фишка привода не защелкивается и привод не работает. 271a обновляет прошивку DVD и жесткого диска, поэтому при их отсутствии вылетает с ошибкой.
- Maverick, Lehrling, MeMpHiSj и 3 другим это нравится
#7
Отправлено 24 августа 2017 - 17:30
Looks like your EVOs have been opened and not properly reassembled. HDD or DVD drive is not properly connected. Make sure to unscrew the adapter board before inserting it into DVD, then screw it back together when DVD is already attached to a connector. Check the drive status in Tool32. If your HDD or DVD is not found, you would not be able to flash 271a - it tries to update the drive firmware and fails when no drive is found. It took me a while to figure this one out. DVD connector is a PITA to connect properly. Must be an easter egg from BMW.
Can you tell me whats the function in tool32?
#8
Отправлено 24 августа 2017 - 18:51
кстати это и к НБТ относится,убил таким образом одну)))))без жесткого ибаки не кладутся,а без двд ,этот свфл максимум смог его до 34 догнать))))
#9
Отправлено 24 августа 2017 - 21:05
Looks like your EVOs have been opened and not properly reassembled. HDD or DVD drive is not properly connected. Make sure to unscrew the adapter board before inserting it into DVD, then screw it back together when DVD is already attached to a connector. Check the drive status in Tool32. If your HDD or DVD is not found, you would not be able to flash 271a - it tries to update the drive firmware and fails when no drive is found. It took me a while to figure this one out. DVD connector is a PITA to connect properly. Must be an easter egg from BMW.
Can you tell me whats the function in tool32?
For HDD look at SMART status - it should display actual values and not 00 or FF. For DVD, the easiest is to try to insert the disc and try ejecting it through tool32 emergency eject.
#10
Отправлено 25 августа 2017 - 07:10
Looks like your EVOs have been opened and not properly reassembled. HDD or DVD drive is not properly connected. Make sure to unscrew the adapter board before inserting it into DVD, then screw it back together when DVD is already attached to a connector. Check the drive status in Tool32. If your HDD or DVD is not found, you would not be able to flash 271a - it tries to update the drive firmware and fails when no drive is found. It took me a while to figure this one out. DVD connector is a PITA to connect properly. Must be an easter egg from BMW.
Can you tell me whats the function in tool32?
For HDD look at SMART status - it should display actual values and not 00 or FF. For DVD, the easiest is to try to insert the disc and try ejecting it through tool32 emergency eject.
what SMART Status, can you clarify please.
I tried ARG;STEUERN_EJECT;STR;4 via tool32, it didnt eject anything
#11
Отправлено 25 августа 2017 - 12:30
Did you have a DVD in it before ejecting?
https://en.wikipedia.../wiki/S.M.A.R.T.
#12
Отправлено 29 августа 2017 - 06:13
I deassembled the idrive, nth in CD drive, HDD seems to be fine, no chips is damaged according to naked eye.
I want your help to check it via teamviewer if you please.
Can arrange a session? you can send me ur email?
mine: m.wahabtoto@gmail.com
Thanks for ur help.
#13
Отправлено 29 августа 2017 - 08:08
#14
Отправлено 29 августа 2017 - 11:14
там в другом засада...просто Интел перелит от американца с 654 опцией,а на еве нет этого разъема..поэтому такая и беда....
#15
Отправлено 29 августа 2017 - 14:29
I inserted a DVD, now i can not eject eject using these.
ARG;STEUERN_EJECT;STR;4 = JOB_STATUS = ERROR_ECU_GENERAL_REJECT
#16
Отправлено 29 августа 2017 - 14:42
I tried ejecting from both units. both of them fails.
#17
Отправлено 29 августа 2017 - 16:43
Check your DVD connection, it is not fully inserted.
там в другом засада...просто Интел перелит от американца с 654 опцией,а на еве нет этого разъема..поэтому такая и беда....
Intel? На EVO?
#18
Отправлено 29 августа 2017 - 17:49
там в другом засада...просто Интел перелит от американца с 654 опцией,а на еве нет этого разъема..поэтому такая и беда....
Американец ? с 654 ?
Могу копать, могу не копать. Могу сделать так чтобы другой копал...
#19
Отправлено 06 сентября 2017 - 04:38
The Radio board is written on it B209 while the unit is B142
The CD rom is not responding to any job in tool32, it makes a sound when i connect it and disconnect it from the body, but no respond from tool32 while putting and ejecting the disk.
#20
Отправлено 06 сентября 2017 - 05:22
DVD and HDD share the controller. If either one is dead, the other may not respond.
Количество пользователей, читающих эту тему: 1
0 пользователей, 1 гостей, 0 анонимных